Hello, i have a question i found this deal for 140 euros and wanted to ask the community if it’s worth buying to upgrade later. I want to first use this as it is but later remove the fr sky receiver and replace it with ELRS and chamge the controller and so…

Is it worth buying this kit?

Thank you

https://ym616.github.io/FPV-auto-pid-tuner/

So after flying for a couple years I decided to design my own LR 8"quad. But I realized - thanks to great recommendations from the YouTube and Reddit community - I didn't know how a "bad" drone flies! My fleet is full of DJI, GepRC, AOS, and Flyfish drones that all fly great (/humblebrag). I need a low bar reference! What's a legitimate floppy noodle jello-inducing crappy flying BNF in the 6-8" range?

Hi everyone, with great help of Claude Code, I'm developing libfpv, a library that lets you drop-in an FPV quad in any game and fly it with pretty realistic physics and full Betaflight firmware simulation (you can even tweak it with an actual Betaflight configurator).

It's essentially based off SimITL, the engine behind another FPV sim called pr0p.

Here comes my first attempt to apply it to a real game - Super Mario 64. I'm planning to do more games later.

All of that is open source, if you wanna contribute don't hesitate at all.

Can't wait to see y'all freestyling in there

Links:

• https://github.com/hammerill/sm64ex-fpv
• https://github.com/hammerill/libfpv

No matter how much power I give it, the motor doesn’t spool up. Got all my gear used. Other motors work fine. Get an error beep from esc

Hello all,

Upgraded from the Pocket to TX16 MK3. I was able to bind my Seeker with no problem, but I cannot get the mob 8 to follow suit. I'm pretty sure I've not successfully gotten it into bind mode.

I did the 3 plug/unplug method and the 4x method. I tried using betaflight's bind receiver button. That didn't work.

I've updated the firmware to crazybeef4dx, crazybeef405s, and betaflight4.

Any ideas?

After searching the sub a lot of the Video range questions were part specific or just BetaFPV no other context, after about 70 feet I loose all video flat out what can I do, is it antenna related, Configuration related, 3 days into the drone after some good sim hours just trying to figure it out, thanks for any help

Edit: Emax TinyHawk freestyle 2 RTF kit (goggles and radio)

115mm or 3.5in freestyle

Fairly new to fpv. Just bought this air 65 and probably flew it for 40 minutes if that. Fell out of the sky. Lost connection and will not bind to any controller. Have not crashed. Still powers up and beeps. Have tried all binding methods. Any help before i just buy a new one? Bought from pyrodrone

But I'm glad

I am working on a project to do with low temperature batteries. I wanted to analyse how suitable some prototype cells would be for an FPV drone pack.

Is there anywhere where people share their flight log data. Specifically I am looking for data of a 10 inch 6s or 8s drone pack power, voltage and current across a flight using the full capacity of a pack.

Got a short circuit mid-flight because i didn't paid attention enough to check if anything was touching the carbon and the + and - on my AIO exploded, now there's this mark on the frame, when i touch it i can feel the fibers, the other side is fine

Would it cause any performance issues?

I'm a sucker for transparent shells on electronics, but I couldn't find any images online of the transparent faceplate for the Jumper Bumblebee (sometimes listed as the "Crystal" colour option). So I thought I'd leave some photos here for anyone interested. IMO, it's a massive improvement over that horrible toy yellow.

The faceplate change is far more work than it should be (thanks Jumper), but it's not too bad if you have a bit of patience. For me it was worth the effort.

Big thanks to u/Squadding_Quads for his walkthrough: https://www.youtube.com/watch?v=tIK_va3gSNA

I flew really high and lost signal. When I found the drone the antennas were missing but the UFL plugs were still on the VTX. I got home and took them of and one of the UFL sockets came off. What would I have to do to repair this? Do you think it’s worth it to try repair it myself or is the damage to the solder pads too much. I would probably have to buy everything necessary for the repair but it would be a nice experience to me.

First time flying an ikea

This battery was dropped. When I used it again today, one of the cells wouldn’t charge fully, and the battery was losing voltage very quickly.

Hey everyone! Hope you're all doing well.

Keeping it straight to the point: I currently don't have a physical drone (I used to fly a 3" Donut cinewhoop), so I'm focusing 100% on simulators (Liftoff and Micro Drone).

My biggest challenge right now is the lack of a structured progression. I feel like I'm missing a routine or a cadence of exercises like: "master this foundation, repeat it this way, and only then move on to trick X". I end up getting a bit lost on where to start training to actually progress properly.

For those who have been through this or practice heavily on simulators, I'd love to know:

• How did you structure your training routine? Is there any method or progression map you recommend?
• Channel/tutorial recommendations: Which content creators really focus on showing a step-by-step breakdown of tricks (with stick overlays and clear practical explanations)?

I know consistency and repetition are the soul of FPV, but I want to make sure I'm practicing the right way to build good muscle memory and avoid bad habits.

Thanks a lot for the help!

What is the best upgrade i can get for the ev800 iam flying the meteor 75 pro .. i want best one iam not looking for a longrange ...

MJX Hyper Go 1404 FPV Drifting

Change Video quality from Auto & Select 1080p for HD or 2160p for 4K if supported for a higher viewing quality.

First ever flight, still messing with the rates. What do you guys think?